General Programme 2024

52MQ

single open end wrenches

SAFETY TESTS: tested at 10,000 V to work on 1,000 V electrical installations. Beta’s high-insulation tools are tested piece by piece at 10 kV, with a view to providing unparalleled quality for working instruments which are required to ensure ultra-high safety standards: they make it possible to work at voltages up to 1,000 V a.c. (1,500 V d.c.). SAFETY STANDARDS: Although extremely stringent tests are performed during production, before using a tool, the operator must always check the insulating handle for tears, modifications or damage. Keeping the dielectric properties unchanged in time is closely connected with the mechanical, chemical or thermal stress the tool may be subjected to. In case the insulator should get damaged, the tool cannot be considered safe for use in live installations. Always wear protective goggles and insulated gloves.

 

L

EN 60900

 mm

L mm

€ 34,00 34,00 34,00 34,00 34,00 34,00 36,00 38,00 39,00 40,50 44,00 44,00 45,50 45,50 49,50 49,50 53,50 70,00 73,00 74,50

 

6 7 8 9

90 96

1 000520106 1 000520107 1 000520108 1 000520109 1 000520110 1 000520111 1 000520112 1 000520113 1 000520114 1 000520115 1 000520116 1 000520117 1 000520118 1 000520119 1 000520121 1 000520122 1 000520124 1 000520127 1 000520130 1 000520132

100 108 110 120 132 140 146 166 156 168 170 176 190 200 225 210 240 240

10 11 12 13 14 15 16 17 18 19 21 22 24 27 30 32

TESTS PERFORMED DURING PRODUCTION

100% visual test: All the surface finishes of the tools must be free from externally visible defects

Crash test: After 2 hours at -25 °C, the tool is hit three times (by such a specific weight as provi- ded for by the standard); the insulating handle must not show any signs of damage.

89MQ

single ring wrenches

-25°

 

L

Penetration test: A weight of 2 kg is applied to the tool handle at +70 °C for two hours. Later a voltage of 5 kV is applied to the area that is subjected to mechanical pressure for 3 minutes. No signs of current passing through must be shown.

EN 60900

 mm

L mm 150 155 155 160 170 180 190 195 200 210 216 218 236 240 250 255 280 300 320 340

€ 43,50 43,50 43,50 43,50 43,50 43,50 47,50 50,50 53,50 54,50 58,00 58,00 62,00 62,00 71,00 71,00 80,50 85,50

 

6 7 8 9

1 000890106 1 000890107 1 000890108 1 000890109 1 000890110 1 000890111 1 000890112 1 000890113 1 000890114 1 000890115 1 000890116 1 000890117 1 000890118 1 000890119 1 000890121 1 000890122 1 000890124 1 000890127 1 000890130 1 000890132

Mechanical test: The tools must satisfy such mechanical performance requirements as provided for in the relevant ISO standards

10 11 12 13 14 15 16 17 18 19 21 22 24 27 30 32

Flame propagation test: A flame is directed towards the tool for 10 seconds; during the next 20 seconds, the flame must not exceed a height of 120 mm.

Dimensional test: All the dimensions of the tools must comply with the design specifications.

100,50 102,00

Electrical insulation test: Following immersion in water for 24 hours, the tool is subjected to a voltage of 10 kV for 3 minutes. Current dissipation must not exceed such values as provided for by the standard.

110MQ

adjustable wrench with scale



500N

L

Adhesion test: after 168 hours at +70 °C, the tool is subjected to a load of 500 N to check that the handle does not slip off.

A

EN 60900

Marking indelibility test: Following the friction test with isopropyl alcohol, markings must remain legible.

L mm 200 250 300

A max 28 30 30

€ 87,00 100,50 146,50

 

1 001100520 1 001100525 1 001100530

286 